UZIN (Germany)

Coatings
	UZIN- MG 318 Blocking coating for parquet. It consists of high quality polymers solution. It gives the surface more r¨¦sistance. Light color of the wood and staining remain . On MG-318, all kinds of UZIN lacquers for parquet and wood for inside works. Mixing with other lacquer systems is impossible! Application area: blocking coating for parquet. Very well for exotic wood . It is good for inside works including furniture. Material spending rate and drying: 50-100ml/sq.m depending on the type of work and special features of the foundation. After each layer, it is necessary to §à bserve drying time ¨C not less than 1 hour with good ventilation. Working with water-based lacquers, it is better to leave them dry out for the night. These drying data are based on normal climate conditions in the room according to DIN 50014
	UZIN-MG 320 One-component water-based base coating for parquet floors with normal load. Spending rate : 70 g / sq . M (when put with a spatula) and 110 g/sq. m (with a roll). Ready to lacquer opening in 50 min. (after it is put with a roll) and in 20 min. (after it is put with a spatula). Application area: on the polished parquet, wooden floors and completely polished ready parquet
	UZIN-MG 325 One-component water-based base coating for parquet floors for strongly absorbing wood species (beech). Spending rate : 70 g / sq . M (applied with a spatula) and 110 g/sq. m (applied with a roll). Ready to lacquer opening in 90 min . ( after applied with a roll ) and in 45 min . (after applied with a spatula). Application area: on the polished parquet, wooden floors and completely polished ready parquet .
	UZIN- MG 345 Gel is a water-based high elastic one-component coating to close the pores before the floor is opened with hydro lacquers. It is convenient for spatula work; it hardens fast. All water lacquers UZIN can be applied on it. Application area: coating for spatula application to close the pores in the wood and for application after the first layer of lacquer. Material spending and drying: depends on the work type and absorbing capacity of the foundation. Orienting parameters: spatula application approx. 20 m 2/§Ý on a layer . Time of interlayer drying: 30 minutes. Then water lacquer is applied. Thickness of the dried layer : 100 g / sq . m /50 m . The data on the drying time are based on normal climate condition according to DIN 50014.
	UZIN- PE 460 Two-component epoxide coating for solidness and hydro isolation of mineral foundations before spackling and gluing the coverings. Spending rate for 1 layer: 200-400 g/sq. m. Drying period: 12-24 hours. It has strengthening, hydro-vapor isolating and protective features. Resistant to chemicals (acids, alkalis). Application area: for internal and outside works in the floor, on mineral water-sensitive foundations, like cement, calcium-sulphate binders, concrete, terrazzo, wood, etc.
	UZIN-PE 317 Adhesion solvent-based coating to apply on the foundations before using the glue UZIN-MK-73. Spending rate : 100-200 g / sq . m . Drying period : 30-60 minutes . Material characteristics: frost-resistant, waterless, deep penetrating, strengthening for internal works. Application area: on concrete, cement, wooden, water-sensitive foundations, like anhydride and cast binders as well as magnesite and xiolyte binders. .
	UZIN-PE 260 L This is a special dispersion to make cross coming carrying off coating layer under conducting or antistatic textile and PVC coverings. A caring off system from a copper band or conducting spackling masses can be made. It is applied on flat, absorbing, mineral foundations, for instance, on cement and calcium-sulphate binders and on all spackled foundations. Applied inn the system with conducting glues UZIN and corresponding floor coverings it prevents from penetrating of potentials tension and electrostatic loads, e.g. in laboratories, workshops, warehouses and operating rooms. It is suitable for water - heated floors .
	UZIN-PE 360 Dispersion coating for absorbing and non-absorbing foundations, walls and floor as well sa internal and outside works. It I good for: cement binders, concrete, foam concrete, ceramics, stone, terrazzo, bricks, cast panels etc. It is specially applied before spackling with cement and cast spackling masses UZIN and before gluing with dispersion glues UZIN on not spackled foundations. Fits the heated floors.
	UZIN-PE 420 Two-component epoxide coating under parquet glue UZIN-MK 92S., §®§¬ -97. Spending rate: 100-150 g/sq.m. Drying period is approx. 2 hours . Application area: cement binders, anhydride and sliding binders, cast asphalt, ceramics, stone, terrazzo, wooden foundations, and aluminum. .